Strap Lock Jam

FWIW, I stopped using Dunlop because the little piece that secures the straplock on the strap shot out of it. I'm certain that was user error during installation. But it's still the reason I avoid them.
and for me, the knob on the Shallers that you lift up kept coming unscrewed.
 
With many acoustic/electric guitars in this day and age, the strap attaches to the end-pin jack, and you can barely get the strap on it. It is a damned poor design, IMO. I did buy this; it works on the Gibson but not the Epiphone.
81DriInnGHL._SL1500_.jpg
 
and for me, the knob on the Shallers that you lift up kept coming unscrewed.

Loctite blue. I've been using Schallers for eight years, and have never had one fail when I use the loctite at the install on the strap. I also use Loctite blue on the nut around input jacks, and have never had a loose nut/jack.
 
Schaller...and Loctite.

I've had issues with the Dunlops in the past. Including the whole device as falling apart on me (not while installed).
 
With many acoustic/electric guitars in this day and age, the strap attaches to the end-pin jack, and you can barely get the strap on it. It is a damned poor design, IMO. I did buy this; it works on the Gibson but not the Epiphone.
Yes that is a MAJOR pain. I don’t understand why they make them that way. Just another 16th of an inch and it wouldn’t be a problem.
 
Yes that is a MAJOR pain. I don’t understand why they make them that way. Just another 16th of an inch and it wouldn’t be a problem.
I don't know why more strap makers haven't designed straps to fit end pin jacks. It seems like a good marketing strategy.
 
How do you like those Dunlop locks? If they work well, I may switch over to them, I hate the way regular strap locks make the guitar hang.
They work fine, just kinda bulky and clunky, seems like they could make them smaller but then they may not be as strong I guess. And they don’t work on acoustic end pin jacks as Gary referenced.
 
I have straplocks on every guitar and bass I own. I used to use mostly Schaller, occasionally Dunlop, but since finding the Marvel Straplocks at GFS many years ago I've moved to them exclusively. In fact, the only guitar that doesn't have the Marvels is my STILL MIA Blue ASAT which has Dunlops. Go figure.

Anyway, I find these far superior in every way to all the others. They will NEVER fail, and if you don't have your Marvel equipped strap on hand for some reason, you can still put a regular strap on it as it doubles as a standard strap button.

The only thing I tell those who are looking into them is that you will occasionally need to apply a few drops of 3 in 1 oil to the spring loaded ball bearing lock mechanism as it can get stiff over time.

1cbf0c80c71fd6151b8bb5ed7bce432c.jpg
89af20b228f51ed1bf689b09210ef1fc.jpg
9873c948fec9dfaea466202a044ca969.jpg
 
I have straplocks on every guitar and bass I own. I used to use mostly Schaller, occasionally Dunlop, but since finding the Marvel Straplocks at GFS many years ago I've moved to them exclusively. In fact, the only guitar that doesn't have the Marvels is my STILL MIA Blue ASAT which has Dunlops. Go figure.

Anyway, I find these far superior in every way to all the others. They will NEVER fail, and if you don't have your Marvel equipped strap on hand for some reason, you can still put a regular strap on it as it doubles as a standard strap button.

The only thing I tell those who are looking into them is that you will occasionally need to apply a few drops of 3 in 1 oil to the spring loaded ball bearing lock mechanism as it can get stiff over time.

1cbf0c80c71fd6151b8bb5ed7bce432c.jpg
89af20b228f51ed1bf689b09210ef1fc.jpg
9873c948fec9dfaea466202a044ca969.jpg

Interesting, haven't seen those before. When you remove the strap do you have to unscrew the bolt?
 
I have straplocks on every guitar and bass I own. I used to use mostly Schaller, occasionally Dunlop, but since finding the Marvel Straplocks at GFS many years ago I've moved to them exclusively. In fact, the only guitar that doesn't have the Marvels is my STILL MIA Blue ASAT which has Dunlops. Go figure.

Anyway, I find these far superior in every way to all the others. They will NEVER fail, and if you don't have your Marvel equipped strap on hand for some reason, you can still put a regular strap on it as it doubles as a standard strap button.

The only thing I tell those who are looking into them is that you will occasionally need to apply a few drops of 3 in 1 oil to the spring loaded ball bearing lock mechanism as it can get stiff over time.

1cbf0c80c71fd6151b8bb5ed7bce432c.jpg
89af20b228f51ed1bf689b09210ef1fc.jpg
9873c948fec9dfaea466202a044ca969.jpg

Those are my favourites as well, although I've got Schallers on a couple. Don't care for the Dunlop.
 
Interesting, haven't seen those before. When you remove the strap do you have to unscrew the bolt?
No, the entire locking assembly stays with the strap. You slide two fingers between the guitar and push the release mechanism to remove the strap. The only thing left behind on the guitar is a notched strap button that can accommodate any other strap without locks. It's very clever.

They are STOUT. The harder you pull on it to see if it will fail, the harder it bites down. You'd rip the strap button and screw out of the guitar well before that lock will give.

The portion that attaches to the strap is equally foolproof. The large diameter flanges on either side of the strap are NEVER going anywhere unless you want them to. Again, you'd break or tear the strap before that hardware fails.

Here's one of my straps with this system:

a1b11282ede125f671da5a50f84787f5.jpg
03ff4d019b6e5e3d61e360bb350097ef.jpg
6a95a438c2b71ea29dd7d0e2a5bdf4f8.jpg
e47fbef4af7acc5c2101b6bef1f7c953.jpg
9245f42dd44c480b5fcef9eefe11ab4c.jpg
5a8e579144fd34d8605a649f4a5ce934.jpg
 
No, the entire locking assembly stays with the strap. You slide two fingers between the guitar and push the release mechanism to remove the strap. The only thing left behind on the guitar is a notched strap button that can accommodate any other strap without locks. It's very clever.

They are STOUT. The harder you pull on it to see if it will fail, the harder it bites down. You'd rip the strap button and screw out of the guitar well before that lock will give.

The portion that attaches to the strap is equally foolproof. The large diameter flanges on either side of the strap are NEVER going anywhere unless you want them to. Again, you'd break or tear the strap before that hardware fails.

Here's one of my straps with this system:

a1b11282ede125f671da5a50f84787f5.jpg
03ff4d019b6e5e3d61e360bb350097ef.jpg
6a95a438c2b71ea29dd7d0e2a5bdf4f8.jpg
e47fbef4af7acc5c2101b6bef1f7c953.jpg
9245f42dd44c480b5fcef9eefe11ab4c.jpg
5a8e579144fd34d8605a649f4a5ce934.jpg

Thanks...I'm gonna check those out
 
  • Like
Reactions: OGG
Pic please!

Sorry, I pulled several guitars out of cases, but since I "color in" the disks with black Sharpie (to blend with the black strap-ends), it's pretty impossible to make out what's what, especially after they're on the guitar. And on a lot of them, I've been putting a layer of duct tape over that, to secure it.

Basically I cut a round disk about an inch and half across, from a credit card. Then I take a scissors and carefully stab into the center, and "drill" out the hole for the strap peg, by turning the scissors until the hole is the right size. The hole should be the same size as the shaft (not the bigger head) of the strap peg.

Of course, if the hole in the disk is only as big as the peg's shaft, it won't fit over the flared peg head, and the only way to get the disk onto the peg would be to take the peg off the guitar and slip the disk on from the bottom (screw) end, then slip the strap on over the bottom end, then screw the peg/disk/strap assembly back onto the guitar. While that's one option, I don't do that.

Once the hole is "drilled" in the center of the plastic disk, I make two staight cuts out from the center hole, just big enough to force the disk over the strap peg end. It looks sorta like this:

40411894822_5f07764a76_o.png


Sometimes I'll just leave the disk like that. If it seems like the straight cuts might allow the disk to come off under stress, I might place a small piece of duct or electrical tape over the disk so the straight cut can't allow the disk to come back off.

Hope that makes sense. I wouldn't do any guitar flips with these, but they work well enough for normal use, in my experience anyhow.
 
I have straplocks on every guitar and bass I own. I used to use mostly Schaller, occasionally Dunlop, but since finding the Marvel Straplocks at GFS many years ago I've moved to them exclusively. In fact, the only guitar that doesn't have the Marvels is my STILL MIA Blue ASAT which has Dunlops. Go figure.

Anyway, I find these far superior in every way to all the others. They will NEVER fail, and if you don't have your Marvel equipped strap on hand for some reason, you can still put a regular strap on it as it doubles as a standard strap button.

The only thing I tell those who are looking into them is that you will occasionally need to apply a few drops of 3 in 1 oil to the spring loaded ball bearing lock mechanism as it can get stiff over time.

1cbf0c80c71fd6151b8bb5ed7bce432c.jpg
89af20b228f51ed1bf689b09210ef1fc.jpg
9873c948fec9dfaea466202a044ca969.jpg

I use those as well. Highly recommended. :thu:
 
  • Like
Reactions: OGG
Back
Top